The performance of tannin-based resins in comparison with melamine-formaldehyde resin for improving the physical and mechanical properties of wood

Document Type : Research Paper

Authors

1 Department of Wood and Paper Science and Technology, Faculty of Natural Resources, University of Tehran, Karaj, Iran.

2 Institute of Conservation and Restoration of Historical-Cultural Artifacts, Research Institute of Cultural Heritage and Tourism (RICHT), Tehran, Iran.

10.22059/jfwp.2024.368424.1268

Abstract

The performance of formaldehyde-free tannin and tannin-resorcinol-formaldehyde resins was investigated in comparison with melamine-formaldehyde resin to improve the physical and mechanical characteristics of oak wood. Melamine-formaldehyde resin was diluted to a concentration of 25% and then 5% carbamide was added to reduce its viscosity. For the synthesis of formaldehyde-free tannin resin, condensed tannin powder with a concentration of 30% in distilled water was used, and the pH was adjusted to the range of 10 using a 33% solution of sodium hydroxide in water. Tannin-resorcinol-formaldehyde resin was also synthesized at pH 8. After impregnation of the wood samples using the empty cell process and drying them with a moisture-based schedule, the resins were cured in an oven at a temperature of 103 ± 2°C for 48 hours and then at a temperature of 120°C for 4 hours. The results showed that modifying wood with all three types of resin leads to a decrease in equilibrium moisture content, improvement in dimensional stability, and surface water repellency. However, it does not have a significant effect on the hardness and modulus of elasticity of the wood. The weight percent gain after modification with melamine-formaldehyde resin (23.8%) was almost twice its value for wood modified with tannin-based resins. Melamine-formaldehyde resin had a better performance in comparison with tannin-based resins, while the intensity of wood color change after modification was also less. The modification process with tannin-resorcinol-formaldehyde resin was more successful in improving the properties compared to formaldehyde-free tannin resin.

Keywords

Main Subjects


[1] Sandberg, D., Kutnar, A., Karlsson, O., & Jones D. (2021). Wood modification technologies: principles, sustainability, and the need for innovation (1st ed.). CRC Press, 442 p.
[2] Bergman, R. (2021). Chapter 13: Drying and control of moisture content and dimensional changes. In: Wood handbook, wood as an engineering material. General Technical Report FPLGTR- 282. Madison, WI: U.S. Department of Agriculture, Forest Service, Forest Products Laboratory. 21 p.
[3] Hill, C.A.S. (2006). Wood Modification Chemical, Thermal and Other Processes, John Wiley and Sons, 260 p.
[4] Gerengi, H., Tascioglu, C., Akcay, C., & Kurtay, M. (2014). Impact of copper chrome boron (CCB) wood preservative on the corrosion of St37 steel. Industrial & Engineering Chemistry Research, 53(49): 19198-19192.
[5] Martinez-Inigo, M. J., Immerzeel, P., Gutierrez, A., del Rio, J.C., & Sierra-Alvarez, R. (1999). Biodegradability of extractives in sapwood and heartwood from scots pine by sapstain and white-rot fungi. Holzforschung, 53: 247-252.
[6] Dorado, J., Van Beek, T., Claassen, F., & Sierra-Alvarez, R. (2001). Degradation of lipophilic wood extractive constituents in Pinus sylvestris by the white rot fungi Bjerkandera sp. and Trametes versicolor. Wood Science and Technology, 35(1-2): 117-125.
[7] Harju, A.M., Venäläinen, M., Anttonen, S., Viitanen, H., Kainulainen, P., Saranpää, P., & Vapaavuori, E. (2003). Chemical factors affecting the brown-rot decay resistance of Scots pine heartwood. Trees, 17(3): 263-268.
[8] Karamać, M. (2009). Chelation of Cu(II), Zn(II), and Fe(II) by tannin constituents of selected edible nuts. International Journal of Molecular Sciences, 10(12): 5485-5497.
[9] Ross, A.R.S., Ikonomou, M.G., & Orians, K.J., (2000). Characterization of dissolved tannins and their metal-ion complexes by electrospray ionization mass spectrometry. Analytica Chimica Acta, 411(1-2): 91-102.
[10] Tondi, G., Oo, C.W., Pizzi, A., Trosa, A., & Thevenon, M. F. (2009). Metal adsorption of tannin based rigid foams. Industrial Crops and Products, 29(2-3): 336-340.
[11] Pizzi, A. (2019). Tannin-Based Biofoams-A Review. Journal of Renewable Materials, 7(16), 474-489.
[12] Thévenon, M.F., Tondi, G., & Pizzi, A. (2010). Environmentally friendly wood preservative system based on polymerized tannin resin-boric acid for outdoor applications. Maderas. Ciencia y Tecnologia, 12(3): 253-257.
[13] Bariska, M., & Pizzi, A. (1986). The Interaction of Polyflavonoid Tannins with Wood Cell-Walls. Holzforschung, 4(5): 299-302.
[14] Militz, H., & Homan, W. J. (1994). Bioassaying combinations of wood preservatives and tannins with poria placenta and aspergillus niger. Holz. als Roh Werkst, 52(1): 28-32.
[15] Ahmadi, ح., Efhamisisi, D., Thevenon ,M., Zare Hosseinabadi, H., Oladi, R., & Gerard, J. (2022). Improvement of physical and mechanical properties of sugarcane bagasse particle board by bagasse treatment with tannin/furfural complex. In : Proceedings of 11èmes Journées Scientifiques du GDR3544 Sciences du bois. Nov. 16-18, Nice, France, pp. 46-50.
[16] Shirmohammadli,Y., Payam Moradpour, P., Abdulkhani, A., Efhamisisi. D., & Pizzi, A. (2019). Water resistance improvement by polyethyleneimine of tannin-furfuryl alcohol adhesives. International Wood Products Journal, 10(1): 16-21.
 [17] Shirmohammadli,Y., Efhamisisi. D., &  Pizzi, A. (2019). Tannins as a sustainable raw material for green chemistry: A review. Industrial Crops and Products, 126(1): 316-332.
 [18] Bajia, S., Sharma, R., & Bajia, B. (2009). Solid-state microwave synthesis of melamine-formaldehyde resin. Journal of Chemistry, 6(1): 120-124.
[19]. Walsh-korb, Z., & Averous, L. (2019). Recent developments in the conservation of materials properties of historical wood. Progress in Material Science, 102: 167-221.
[20] Ahmadi, P., Efhamisisi, D., Pourtahmasi, K., & Izadyar; S. (2019). The investigation of physico-mechanical characteristics of poplar wood impregnated with melamine formaldehyde resin. Journal of Forest and Wood Products, 72(3): 249-261. (In Persian)
[21] Theis, M., & Grohe, B. (2002). Biodegradable lightweight construction boards based on tannin/hexamine bonded hemp shaves. Holz Roh Werkst, 60(4): 291-296.
[22] Efhamisisi, D., Thevenon, M.F., Hamzeh, Y., Pizzi, A., Karimi, A.N., & Pourtahmasi, K. (2015). Acceleration of self-compacting reactions of cobraco tannin wood glue with boric acid. Journal of Forest and Wood Products, 68(1): 149-160. (In Persian)
[23] Tondi, G., Thevenon, M.F., Mies, B., Standfest, G., Petutschnigg, A., & Wieland, S. (2013). Impregnation of Scots pine and beech with tannin solutions: effect of viscosity and wood anatomy in wood infiltration. Wood Science and Technology, 47: 615-626.
[24] Tondi, G. (2019). Effect of hardening parameters of wood preservatives based on tannin copolymers. Holzforschung, 73(5): 457-4.
[25] Efhamisisi, D., Thevenon, M.F., Hamzeh, Y., Karimi, A.N., Pizzi, A., & Pourtahmasi, K. (2016). Induced tannin adhesive by boric acid addition and its effect on bonding quality and biological performance of poplar plywood. ACS Sustainable Chemistry & Engineering, 4(5): 2734-2740.
[26] Efhamisisi, D., Thevenon, M.F., Hamzeh, Y., Pizzi, A., Karimi, A.N., & Pourtahmasi, K. (2017). Tannin-boron complex as a preservative for 3-ply beech plywoods designed for humid conditions. Holzforschung, 71(9): 249-258.
[27] Sauget, A., Zhou, X., & Pizzi, A. (2014). Tannin-Resorcinol-Formaldehyde Resin and Flax Fiber Biocomposites. Scrivener Publishing LLC, Journal of Renewable Materials, 2(3): 173-181.
[28] NF X 41-568. AFNOR. (2010). Wood preservatives laboratory method for obtaining samples for analysis to measure losses by leaching into water or synthetic seawater.
[29] Karimi, Z. (2020). Systematic study of the wood anatomy of some species of the Fagaceae family with an ecological interpretation. Rostaniha, 21(1): 1-13.
[30] Tondi, G., Schnabel, T., Wieland, S., & Petutschnigg, A. (2013). Surface properties of tannin treated wood during natural and artificial weathering. International Wood Products Journal, 4(3): 150-157.
[31] Ahmadi, p., Efhamisisi, D., Thevenon, M., Zare Hosseinabadi, H., Oladi, R., & Gerard, J. (2022). The properties of natural tannin-furfural resin applied to Poplar wood modification. Journal of Wood and Forest Science and Technology, 29(2): 1-20. (In Persian)
[32] Deka, M., Gindl, W., Wimmer, R., & Christian, H. (2007). Chemical modification of Norway spruce (Picea abies (L) Karst) wood with melamine formaldehyde resin. Indian Journal of Chemical Technology, 14(2): 134-138.
[33] Hazarika, A., Deka, B.K., & Maji, T.K. (2015). Melamine-formaldehyde acrylamide and gum polymer impregnated wood polymer nanocomposite. Journal of Bionic Engineering, 12(2): 304-315.
[34] Kielmann, B. C., Militz, H., & Mai, C. (2016). The effect of combined melamine resin colouring agent modification on water-related properties of beech wood. Wood Resslovakia, 61(1): 1-12.
[35] Tondi, G., Wieland, S., Wimmer, T., Thevenon, M.F., Pizzi, A., & Petutschnigg, A. (2012). Tannin-boron preservatives for wood buildings: mechanical and fire properties. European Journal of Wood and Wood Products, 70(5): 689-696.
[36] Gindl, W., & Gupta, H. S. (2002). Cell-wall hardness and Young’s modulus of melamine-modified spruce wood by nano-indentation, Composites Part A: Applied Science and Manufacturing, 33(8): 1141-1145.
 [37] Talaei, A., Mahmoudi, T., & Abdolzadeh, H. (2021). Study on thermal behavior and contact angle of Furfurylated poplar wood-polymer. Journal of Wood and Forest Science and Technology, 27(4): 19-23. (In Persian)