@article { author = {Abdolkhani, Ali and Hoseinzadeh, Jaber and Hedjazi, Sahab}, title = {Characterization of Cellulose Reinforced Polylactic Acid Solution Cast Nanocomposite}, journal = {Forest and Wood Products}, volume = {67}, number = {2}, pages = {271-282}, year = {2014}, publisher = {University of Tehran}, issn = {5052-2008}, eissn = {2383-0530}, doi = {10.22059/jfwp.2014.51546}, abstract = {Polylactic acid based Biodegradable nanocomposites reinforced with acetylated nanocellulose were fabricated with solution casting procedure. The nanocomposites were prepared by adding 1, 3 and 5% nanofiber loadings. The microstructure, physical, mechanical and thermal properties of the prepared nanocomposites were investigated. Scanning electronic microscope (SEM) analysis of the composites confirmed the uniform distribution of nanoparticles within the matrix at low percentages. According to water vapor barrier test results, acetylated fibers did not improve the permeability of the prepared composites. Tensile strength (elongation) of nanocomposites had improved significantly by reinforcing with nanofibers due to the good dispersion of nanofibers at 1 and 3 percent, while the increase of nanofiber led to an aggregation and a brittle film with increased modulus of elasticity. Reinforcing effect of nanocellulose caused an increase in glass transition and melting temperature of the composites. However, the thermal behavior of nanocomposite and pure PLA films showed a very similar pattern.}, keywords = {biodegradable polymer,Cellulose Nanofiber,mechanical properties,Microstructure,polylactic acid,Thermal properties}, title_fa = {بررسی ویژگی‏های نانوچندسازه‏های تهیه‏شده از پلی‏‏لاکتیک اسیدِ تقویت‏‏شده با نانو‌الیاف سلولزی}, abstract_fa = {نانو کامپوزیت‌های زیست تخریب‌پذیر بر پایة پلی‌لاکتیک اسید، تقویت‌شده با نانو الیاف سلولز استیله شده و با روش قالب‌ریزی حلال و در فاز محلول ساخته شدند. نانو الیاف در سه سطح 1 ،3 و 5 درصد وزن فیلم اضافه شد. ریزساختار، بازدارندگی، همچنین خواص مکانیکی، فیزیکی و حرارتی نانوکامپوزیت‌ها مطالعه شد. ریزنگاره‌های میکروسکوپ الکترونی توزیع یکنواخت نانوذرات در ماتریس پلیمر در درصدهای کم را نشان داد و نتایج آزمون‌های دیگر را تأیید کرد. نتایج حاصل از نفوذپذیری آزمون‌های بخار آب نشان داد که استفاده از نانوالیاف استیله آثار قابل توجهی در نفوذپذیری فیلم نداشت. با توجه به پراکنش خوب نانو الیاف در سطح 1 و 3 درصد خواص کشش‌پذیری (افزایش طول) نانو کامپوزیت بهبود قابل توجهی داشت ولی با افزایش درصد نانو الیاف، تجمع بین الیاف زیاد شد و نانو کامپوزیت از حالت پلاستیکی خارج و تبدیل به ماده‌ای سخت و شکننده می‌شود. این امر باعث افزایش قابل توجه در مدول الاستیسیته می‌شود. اثر تقویت‌کنندگی نانوالیاف در ترکیب با پلی‌لاکتیک اسید باعث افزایش کمی در دمای گذر شیشه‌ای و درجه حرارت ذوب‌شدن شد. با این حال، رفتار حرارتی فیلم‌های نانوکامپوزیتی الگوی بسیار مشابه به فیلم PLA خالص را نشان می‌دهد.}, keywords_fa = {پلی‌لاکتیک اسید,پلیمر زیست‌تخریب‌پذیر,خواص حرارتی,خواص مکانیکی,ریزساختار,نانوالیاف سلولز}, url = {https://jfwp.ut.ac.ir/article_51546.html}, eprint = {https://jfwp.ut.ac.ir/article_51546_8010a629e7cbe0ea9081260d80fbc165.pdf} }